tube bending machine
|
SINGLE-BEND
TUBE BENDER
|
 CR-A38SA |
|
TYPE
|
O.D.
* Wall
(mm) |
Range
of Radius
(mm) |
Range
of Bending
|
Horse
Power
|
Total
Length
|
Total
Width
|
Total
Height
|
Total
Weight
|
Range
of Bending Speed
|
Angel
|
|
CR-A38SA
|
38*2.5
|
10~350
|
0
 ~210 |
5HP
|
1500mm
|
700mm
|
1100mm
|
700kg
|
90
3~4/sec |
1
|
|
SINGLE-BEND
TUBE BENDER WITH MANDREL
|
 CR-B44SQ |
|
TYPE
|
O.D.
* Wall
(mm) |
Range
of Radius
(mm) |
Range
of Bending
|
Horse
Power
|
Total
Length
|
Total
Width
|
Total
Height
|
Total
Weight
|
Range
of Bending Speed
|
Angel
|
|
CR-B44SQ
|
45*2.5
|
10~250
|
0
~190 |
5HP
|
2400mm
|
800mm
|
1000mm
|
1100kg
|
90
3~4/sec |
2
|
| SINGLE-BEND TUBE BENDER WITH MANDREL | ||
 |
Adopting solenoid valve and integrated circuit to control every motion separately. | |
|
Three-step circuit is with the functions of cooling & sedimentation to keep hydraulic oil from deterioration. | |
|
Main shaft is heat-treated specially and the bending arm is made of special forged steel. All the parts are made under very strict quality control so that the quality of machine is good & the specification is standardized. | |
|
The machine is with emergency stop device. | |
|
Both manual and automatic operation are available. | |
|
Various angles can be set. You can bend one pipe with several bending on one machine only to save the time of re-loading & unloading among different machines. | |
|
The control panel has clear description for every button / gauge, so non-technician still can operate our machine correctly. | |
|
Can be equipped with an automatic feeding device. This device has the function of pipe length setting up. Besides, our machine (NC type) can make 10-angle bending with the Japanese-made micro encoder at the same time. Due to these 2 factors, our machine can produce many kinds of sophisticated / complicated bending-pipe as client's wish and the clients spend much less labor cost than using other brand machines. | |
|
With our NC type machines, client can bend the pipes as their own wishes if they make right adjustments on 3 points: | |
| (1) | The stroke of automatic feeding device. | |
| (2) | The angle of bending. | |
| (3) | The number of feeding. | |
|
TUBE
END-FORMING MACHINE
|
 CR-C38 |
 |
 CR-C60A2 |
 |
||
|
TYPE
|
O.D.
* Wall
(mm) |
Range
of Pipe
(mm) |
Horse
Power
|
Pipe
Shrinking Speed
|
Total
Length
|
Total
Width
|
Total
Height
|
Total
Weight
|
|
CR-C38
|
38*2.0
|
150
|
5HP
|
100mm
1.5/sec
|
2000mm
|
500mm
|
1200mm
|
1000kg
|
|
CR-C60A2
|
60*3.0
|
250
|
15HP
|
100mm
2.5/sec
|
3000mm
|
800mm
|
1400mm
|
2000kg
|
| TUBE END-FORMING MACHINE | |
|
Suitable for the
shrinking of various metal pipes with |
|
All the parts are made under very strict quality control, so the quality of machine is in high level and the specification is standardized. |
|
Equipped with emergency stop device. Both manual & automatic operations are available. |
|
Shrinking stroke 150m/m. The length of working piece is 4,500 m/m Max. (but on limit on the minimum length.) |
|
An additional feeding system can be added to the machine. The oprating security is greatly increased because the operators just do the unloading & collecting job of finished pipes. |
|
Forming shapes can be convex, concave, sectional, long & flat, square, V-shap, open elbow, flat elbow...etc. The design of the tooling varies with work-piece & customers' requirements. |
| < products memu >next page | |
